ProtoxAkvagrund2 is a wood protection for the initial treatment of new and old outdoor woodwork that must be protected against rot, fungus and blue splinter.
- Prevents against rot, fungus, blue splinter and mould
- Seals mold infestation in inaccessible places such as roof structures, inside wall structures and under tiled floors
- Can be used on untreated, outdoor woodwork – new and old – e.g. windows, doors, wooden decks, fences and carports
The advantages of ProtoxAkvagrund2
One wood preservative that protects against rot, fungus, mold and blue splinter while being easy to use. This is precisely what ProtoxAkvagrund2 is and can do. It saves you working time. And then ProtoxAkvagrund2 has the lowest MAL code of 00-1, so that you meet the requirements of the working environment legislation to choose the least dangerous product when you choose ProtoxAkvagrund2.
If you need to treat a mold attack in a hard-to-reach place, ProtoxAkvagrund2 is also the obvious choice. The agent seals mold attacks where it is not physically or financially possible to remove them ProtoxHysan. Such inaccessible locations may be:
- Roof constructions with sloping walls
- Plywood sub-ceiling
- Chipboard in wall constructions
- Plaster inside wall structures
- Under tiled floors
- In cable channels
ProtoxAkvagrund2 has been tested and approved
ProtoxAkvagrund2 has all the necessary approvals according to Danish and EU legislation. The product is tested against blue splinter, rot and fungus and approved according to EN standards EN 84, EN 73 and EN 152.1.
ProtoxAkvagrund2 has MAL 00-1, so you meet the requirements of the occupational health and safety legislation to choose the least dangerous product when working with ProtoxAkvagrund2. The product is also not classified as dangerous, harmful to health or similar.
ProtoxAkvagrund2 is approved in Denmark with the number MST 578-23-1.
ProtoxAkvagrund2 is approved in Sweden with the number 4745-1-1.
ProtoxAkvagrund2 is approved in Norway with the number NO-2013-0028.
Application of ProtoxAkvagrund2
What is ProtoxAkvagrund2?
ProtoxAkvagrund2 is a colourless, water-based agent to protect untreated outdoor woodwork against rot, fungus, mold and blue splinter. The product can also seal inaccessible areas against mold growth, e.g. roof structures, inside wall structures and under tiled floors.
ProtoxAkvagrund2 is very odorless and after drying there is no smell at all.
Be aware that a surface treated with ProtoxAkvagrund2 will have its potential vapor permeability reduced. A surface treated with ProtoxAkvagrund2 can therefore act as a vapor barrier. Remember to take this into account when choosing a treatment method.
Where do you use ProtoxAkvagrund2?
- Used on new and old, untreated, outdoor woodwork
- Can be used for wood protection on e.g. windows, doors, wooden terraces, coverings, eaves, wind deflectors, fences, carports and under-roofs made of plywood or other wooden materials
- Can be used to seal mold growth, e.g. on roof structures, inside wall structures and under tiled floors
- Used on wood with a temperature above 5°C, a relative humidity below 80 % and a wood moisture below 18 %
Preparation
ProtoxAkvagrund2 is ready to use and must not be diluted further.
The range is 4-6 m2 per litres, but it depends a lot on the absorbency of the wood. On new wood, the product can reach up to 8 m2 per litres.
The product must be stirred before use.
Ensure good ventilation during the treatment and during the drying period.
Always read the safety data sheet before using the product.
Application
ProtoxAkvagrund2 can be applied with a brush, by spraying, dipping or application machine.
Avoid spillage of the product on the ground or in watercourses.
Always carry out the treatment on a reinforced surface or with a cover.
Aftertreatment
The drying time is approx. 1-2 hours before the surface is dry to the touch and approx. 24 hours until it is ready for overpainting. Drying is best done at a temperature of 23°C and a relative humidity of 60 %.
Utensils and tools are cleaned with soap and water after use.
ProtoxAkvagrund2 is stable for at least 2 years in unopened packaging and must be stored frost-free.
Empty packaging and leftovers can be thrown away with the household waste.
If wood treated with ProtoxAkvagrund2 is exposed to wind and weather, it must be protected with a surface treatment, which must be continuously maintained according to the manufacturer's instructions. All water-based products for outdoor woodwork can be used.
Also read
Packaging sizes
5.0 liter plastic can
CLP Classification
Harmful to aquatic organisms, with long-lasting effects.
‘Use biocides safely. Always read the label and product information before use.’
Few overview about our products
Our product catalog contains guides and descriptions etc